200-301: Cisco Certified Network Associate (CCNA) → 200-301: Cisco Certified Network Associate (CCNA) Part 8

200-301: Cisco Certified Network Associate (CCNA) Part 8

Question #: 421
Topic #: 1
Which MAC address is recognized as a VRRP virtual address?

A. 0000.5E00.010a
B. 0005.3709.8968
C. 0000.0C07.AC99
D. 0007.C070.AB01

Selected Answer: A

Question #: 422
Topic #: 1
Refer to the exhibit. The New York router is configured with static routes pointing to the Atlanta and Washington sites.
Which two tasks must be performed so that the Se0/0/0 interfaces on the Atlanta and Washington routers reach one another? (Choose two.)

A. Configure the ipv6 route 2023::/126 2012::1 command on the Atlanta router.
B. Configure the ipv6 route 2012::/126 2023::2 command on the Washington router.
C. Configure the ipv6 route 2012::/126 2023::1 command on the Washington router.
D. Configure the ipv6 route 2023::/126 2012::2 command on the Atlanta router.
E. Configure the ipv6 route 2012::/126 s0/0/0 command on the Atlanta router.

Selected Answer: BD

Question #: 423
Topic #: 1
A router running EIGRP has learned the same route from two different paths. Which parameter does the router use to select the best path?

A. as-path
B. administrative distance
C. metric
D. cost

Selected Answer: C

Question #: 424
Topic #: 1
An engineer configured an OSPF neighbor as a designated router. Which state verifies the designated router is in the proper mode?

A. Init
B. 2-way
C. Exchange
D. Full

Selected Answer: D

Question #: 425
Topic #: 1
Refer to the exhibit. Which route does R1 select for traffic that is destined to 192.168.16.2?

A. 192.168.16.0/21
B. 192.168.16.0/24
C. 192.168.16.0/26
D. 192.168.16.0/27

Selected Answer: D

Question #: 426
Topic #: 1
Refer to the exhibit. If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command, how does the router respond?

A. It starts sending traffic without a specific matching entry in the routing table to GigabitEthernet0/1.
B. It immediately replaces the existing OSPF route in the routing table with the newly configured static route.
C. It starts load-balancing traffic between the two default routes.
D. It ignores the new static route until the existing OSPF default route is removed.

Selected Answer: D

Question #: 427
Topic #: 1
Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)

A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.

Selected Answer: DF

Question #: 428
Topic #: 1
Refer to the exhibit. Which command configures a floating static route to provide a backup to the primary link?

A. ip route 209.165.200.224 255.255.255.224 209.165.202.129 254
B. ip route 209.165.201.0 255.255.255.224 209.165.202.130
C. ip route 0.0.0.0 0.0.0.0 209.165.200.224
D. ip route 0.0.0.0 0.0.0.0 209.165.202.131

Selected Answer: A

Question #: 429
Topic #: 1
Refer to the exhibit. An engineer configured the New York router with static routes that point to the Atlanta and Washington sites. Which command must be configured on the Atlanta and Washington routers so that both sites are able to reach the loopback2 interface on the New York router?

A. ipv6 route::/0 Serial 0/0/0
B. ipv6 route::/0 Serial 0/0/1
C. ipv6 route:0/0 Serial 0/0/0
D. ip route 0.0.0.0 0.0.0.0 Serial 0/0/0
E. ipv6 route::/0 2000::2

Selected Answer: A

Question #: 430
Topic #: 1
What is the effect when loopback interfaces and the configured router ID are absent during the OSPF Process configuration?

A. The lowest IP address is incremented by 1 and selected as the router ID.
B. The router ID 0.0.0.0 is selected and placed in the OSPF process.
C. No router ID is set, and the OSPF protocol does not run.
D. The highest up/up physical interface IP address is selected as the router ID.

Selected Answer: D

Question #: 431
Topic #: 1
Refer to the exhibit. What is the metric of the route to the 192.168.10.33/28 subnet?

A. 84
B. 110
C. 128
D. 192
E. 193

Selected Answer: E

Question #: 432
Topic #: 1
Refer to the exhibit. Traffic sourced from the loopback0 interface is trying to connect via ssh to the host at 10.0.1.15. What is the next hop to the destination address?

A. 192.168.0.7
B. 192.168.0.4
C. 192.168.0.40
D. 192.168.3.5

Selected Answer: A

Question #: 433
Topic #: 1
When the active router in a VRRP group fails, which router assumes the role and forwards packets?

A. forwarding
B. standby
C. backup
D. listening

Selected Answer: C

Question #: 434
Topic #: 1
Which action does the router take as it forwards a packet through the network?

A. The router encapsulates the original packet and then includes a tag that identifies the source router MAC address and transmits it transparently to the destination.
B. The router encapsulates the source and destination IP addresses with the sending router IP address as the source and the neighbor IP address as the destination.
C. The router replaces the original source and destination MAC addresses with the sending router MAC address as the source and neighbor MAC address as the destination.
D. The router replaces the source and destination labels with the sending router interface label as a source and the next hop router label as a destination.

Selected Answer: C

Question #: 435
Topic #: 1
Refer to the exhibit. Which two prefixes are included in this routing table entry? (Choose two.)

A. 192.168.1.17
B. 192.168.1.61
C. 192.168.1.64
D. 192.168.1.127
E. 192.168.1.254

Selected Answer: AB

Question #: 436
Topic #: 1
Which virtual MAC address is used by VRRP group 1?

A. 0504.0367.4921
B. 0007.c061.bc01
C. 0050.0c05.ad81
D. 0000.5E00.0101

Selected Answer: D

Question #: 437
Topic #: 1
What is the purpose of using First Hop Redundancy Protocol on a specific subnet?

A. forwards multicast hello messages between routers
B. sends the default route to the hosts on a network
C. ensures a loop-free physical topology
D. filters traffic based on destination IP addressing

Selected Answer: B

Question #: 438
Topic #: 1
What is the purpose of using First Hop Redundancy Protocol on a specific subnet?

Selected Answer: B

Question #: 439
Topic #: 1
Refer to the exhibit. Which configuration issue is preventing the OSPF neighbor relationship from being established between the two routers?

A. R1 has an incorrect network command for interface Gi1/0.
B. R2 should have its network command in area 1.
C. R1 interface Gi1/0 has a larger MTU size.
D. R2 is using the passive-interface default command.

Selected Answer: C

Question #: 440
Topic #: 1
Refer to the exhibit. When router R1 is sending traffic to IP address 10.56.192.1, which interface or next hop address does it use to route the packet?

A. 10.56.0.1
B. 0.0.0.0/0
C. Vlan57
D. 10.56.128.19

Selected Answer: A

Question #: 441
Topic #: 1
Refer to the exhibit. Load-balanced traffic is coming in from the WAN destined to a host at 172.16.1.190. Which next-hop is used by the router to forward the request?

A. 192.168.7.4
B. 192.168.7.7
C. 192.168.7.35
D. 192.168.7.40

Selected Answer: C

Question #: 442
Topic #: 1
What is a benefit of VRRP?

A. It provides the default gateway redundancy on a LAN using two or more routers.
B. It provides traffic load balancing to destinations that are more than two hops from the source.
C. It prevents loops in a Layer 2 LAN by forwarding all traffic to a root bridge, which then makes the final forwarding decision.
D. It allows neighbors to share routing table information between each other.

Selected Answer: A

Question #: 443
Topic #: 1
Refer to the exhibit. Routers R1 and R3 have the default configuration. The router R2 priority is set to 99. Which commands on R3 configure it as the DR in the
10.0.4.0/24 network?

A. R3(config)#interface Gig0/0 R3(config-if)#ip ospf priority 100
B. R3(config)#interface Gig0/0 R3(config-if)#ip ospf priority 1
C. R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 0
D. R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 100

Selected Answer: D

Question #: 444
Topic #: 1
Refer to the exhibit. A network engineer must configure R1 so that it sends all packets destined to the 10.0.0.0/24 network to R3, and all packets destined to PC1 to R2. Which configuration must the engineer implement?

A. R1(config)#ip route 10.0.0.0 255.255.255.0 172.16.0.2 R1(config)#ip route 10.0.0.5 255.255.255.255 192.168.0.2
B. R1(config)#ip route 10.0.0.0 255.255.0.0 172.16.0.2 R1(config)#ip route 10.0.0.5 255.255.255.255 192.168.0.2
C. R1(config)#ip route 10.0.0.0 255.255.255.0 192.168.0.2 R1(config)#ip route 10.0.0.5 255.255.255.255 172.16.0.2
D. R1(config)#ip route 10.0.0.0 255.255.0.0 192.168.0.2 R1(config)#ip route 10.0.0.5 255.255.255.0 172.16.0.2

Selected Answer: C

Question #: 445
Topic #: 1
Refer to the exhibit. All traffic enters the CPE router from interface Serial0/3 with an IP address of 192.168.50.1. Web traffic from the WAN is destined for a LAN network where servers are load-balanced. An IP packet with a destination address of the HTTP virtual IP of 192.168.1.250 must be forwarded. Which routing table entry does the router use?

A. 192.168.1.0/24 via 192.168.12.2
B. 192.168.1.128/25 via 192.168.13.3
C. 192.168.1.192/26 via 192.168.14.4
D. 192.168.1.224/27 via 192.168.15.5

Selected Answer: D

Question #: 446
Topic #: 1
Refer to the exhibit. All traffic enters the CPE router from interface Serial0/3 with an IP address of 192.168.50.1. Web traffic from the WAN is destined for a LAN network where servers are load-balanced. An IP packet with a destination address of the HTTP virtual IP of 192.168.1.250 must be forwarded. Which routing table entry does the router use?

A. 192.168.1.0/24 via 192.168.12.2
B. 192.168.1.128/25 via 192.168.13.3
C. 192.168.1.192/26 via 192.168.14.4
D. 192.168.1.224/27 via 192.168.15.5

Selected Answer: D

Question #: 447
Topic #: 1
Refer to the exhibit. An engineer assumes a configuration task from a peer. Router A must establish an OSPF neighbor relationship with neighbor 172.1.1.1. The output displays the status of the adjacency after 2 hours. What is the next step in the configuration process for the routers to establish an adjacency?

A. Configure router A to use the same MTU size as router B.
B. Configure a point-to-point link between router A and router B.
C. Set the router B OSPF ID to the same value as its IP address.
D. Set the router B OSPF ID to a nonhost address.

Selected Answer: A

Question #: 448
Topic #: 1
Refer to the exhibit. Which two configurations must the engineer apply on this network so that R1 becomes the DR? (Choose two.)

A. R3(config)#interface fastethernet 0/0 R3(config-if)#ip ospf priority 0
B. R1(config)#router ospf 1 R1(config-router)#router-id 192.168.100.1
C. R1(config)#interface fastethernet 0/0 R1(config-if)#ip ospf priority 200
D. R1(config)#interface fastethernet 0/0 R1(config-if)#ip ospf priority 0
E. R3(config)#interface fastethernet 0/0 R3(config-if)#ip ospf priority 200

Selected Answer: AC

Question #: 449
Topic #: 1
Refer to the exhibit. Which command configures OSPF on the point-to-point link between routers R1 and R2?

A. router-id 10.0.0.15
B. neighbor 10.1.2.0 cost 180
C. network 10.0.0.0 0.0.0.255 area 0
D. ip ospf priority 100

Selected Answer: C

Question #: 450
Topic #: 1
Refer to the exhibit. A network engineer is in the process of establishing IP connectivity between two sites. Routers R1 and R2 are partially configured with IP addressing. Both routers have the ability to access devices on their respective LANs. Which command set configures the IP connectivity between devices located on both LANs in each site?

A. R1 ip route 192.168.1.1 255.255.255.0 GigabitEthernet0/1 R2 ip route 10.1.1.1 255.255.255.0 GigabitEthernet0/1
B. R1 ip route 192.168.1.0 255.255.255.0 GigabitEthernet0/0 R2 ip route 10.1.1.1 255.255.255.0 GigabitEthernet0/0
C. R1 ip route 0.0.0.0 0.0.0.0 209.165.200.225 R2 ip route 0.0.0.0 0.0.0.0 209.165.200.226
D. R1 ip route 0.0.0.0 0.0.0.0 209.165.200.226 R2 ip route 0.0.0.0 0.0.0.0 209.165.200.225

Selected Answer: C

Question #: 451
Topic #: 1
Refer to the exhibit. Which next-hop IP address does Router1 use for packets destined to host 10.10.13.158?

A. 10.10.10.9
B. 10.10.10.5
C. 10.10.11.2
D. 10.10.12.2

Selected Answer: A

Question #: 452
Topic #: 1
Refer to the exhibit. Packets received by the router from BGP enter via a serial interface at 209.165.201.1. Each route is present within the routing table. Which interface is used to forward traffic with a destination IP of 10.1.1.19?

A. F0/0
B. F0/1
C. F0/4
D. F0/3

Selected Answer: A

Question #: 453
Topic #: 1
Refer to the exhibit. Which route must be configured on R1 so that OSPF routing is used when OSPF is up, but the server is still reachable when OSPF goes down?

A. ip route 10.1.1.10 255.255.255.255 gi0/0 125
B. ip route 10.1.1.0 255.255.255.0 172.16.2.2 100
C. ip route 10.1.1.0 255.255.255.0 gi0/1 125
D. ip route 10.1.1.10 255.255.255.255 172.16.2.2 100

Selected Answer: A

Question #: 454
Topic #: 1
Refer to the exhibit. What is the next hop for traffic entering R1 with a destination of 10.1.2.126?

A. 10.165.20.126
B. 10.165.20.146
C. 10.165.20.166
D. 10.165.20.226

Selected Answer: A

Question #: 455
Topic #: 1
Refer to the exhibit. Which prefix did router R1 learn from internal EIGRP?

A. 192.168.3.0/24
B. 192.168.1.0/24
C. 172.16.1.0/24
D. 192.168.2.0/24

Selected Answer: D

Question #: 456
Topic #: 1
Refer to the exhibit. R5 is the current DR on the network, and R4 is the BDR. Their interfaces are flapping, so a network engineer wants the OSPF network to elect a different DR and BDR. Which set of configurations must the engineer implement?

A. R4(config)#interface gi0/0 R4(config-if)#ip ospf priority 20 R5(config)#interface gi0/0 R5(config-if)#ip ospf priority 10
B. R5(config)#interface gi0/0 R5(config-if)#ip ospf priority 120 R4(config)#interface gi0/0 R4(config-if)#ip ospf priority 110
C. R3(config)#interface gi0/0 R3(config-if)#ip ospf priority 255 R2(config)#interface gi0/0 R2(config-if)#ip ospf priority 240
D. R2(config)#interface gi0/0 R2(config-if)#ip ospf priority 259 R3(config)#interface gi0/0 R3(config-if)#ip ospf priority 256

Selected Answer: C

Question #: 457
Topic #: 1
Refer to the exhibit. Web traffic is coming in from the WAN interface. Which route takes precedence when the router is processing traffic destined for the LAN network at 10.0.10.0/24?

A. via next-hop 10.0.1.5
B. via next-hop 10.0.1.4
C. via next-hop 10.0.1.50
D. via next-hop 10.0.1.100

Selected Answer: A

Question #: 458
Topic #: 1
Refer to the exhibit. A packet sourced from 10.10.10.1 is destined for 10.10.8.14. What is the subnet mask of the destination route?

A. 255.255.254.0
B. 255.255.255.240
C. 255.255.255.248
D. 255.255.255.252

Selected Answer: B

Question #: 459
Topic #: 1
Refer to the exhibit. An engineer must configure router R2 so it is elected as the DR on the WAN subnet. Which command sequence must be configured?

A. interface gigabitethernet0/0 ip address 10.0.0.34 255.255.255.248 ip ospf priority 0
B. interface gigabitethernet0/0 ip address 10.0.0.34 255.255.255.224 ip ospf priority 100
C. interface gigabitethernet0/0 ip address 10.0.1.1 255.255.255.0 ip ospf priority 255
D. interface gigabitethernet0/0 ip address 10.0.1.1 255.255.255.224 ip ospf priority 98

Selected Answer: B

Question #: 460
Topic #: 1
An engineer is configuring router R1 with an IPv6 static route for prefix 2019:C15C:0CAF:E001::/64. The next hop must be 2019:C15C:0CAF:E002::1. The route must be reachable via the R1 Gigabit 0/0 interface. Which command configures the designated route?

A. R1(config-if)#ip route 2019:C15C:0CAF:E001::/64 GigabitEthernet 0/0
B. R1(config)#ip route 2019:C15C:0CAF:E001::/64 GigabitEthernet 0/0
C. R1(config-if)#ipv6 route 2019:C15C:0CAF:E001::/64 2019:C15C:0CAF:E002::1
D. R1(config)#ipv6 route 2019:C15C:0CAF:E001::/64 2019:C15C:0CAF:E002::1

Selected Answer: D

Question #: 461
Topic #: 1
Refer to the exhibit. Which IPv6 configuration is required for R17 to successfully ping the WAN interface on R18?

A. R17# ! no ip domain lookup ip cef ipv6 cef ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:4::302
B. R17# ! no ip domain lookup ip cef ipv6 unicast-routing ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:3::301
C. R17# ! no ip domain lookup ip cef ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:5::101
D. R17# ! no ip domain lookup ip cef ipv6 unicast-routing ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:2::201

Selected Answer: B

Question #: 462
Topic #: 1
Refer to the exhibit. A company is configuring a failover plan and must implement the default routes in such a way that a floating static route will assume traffic forwarding when the primary link goes down. Which primary route configuration must be used?

A. ip route 0.0.0.0 0.0.0.0 192.168.0.2
B. ip route 0.0.0.0 0.0.0.0 192.168.0.2 GigabitEthernet1/0
C. ip route 0.0.0.0 0.0.0.0 192.168.0.2 floating
D. ip route 0.0.0.0 0.0.0.0 192.168.0.2 tracked

Selected Answer: A

Question #: 463
Topic #: 1
OSPF must be configured between routers R1 and R2. Which OSPF configuration must be applied to router R1 to avoid a DR’BDR election?

A. router ospf 1 network 192.168.1.1 0.0.0.0 area 0 interface e1/1 ip address 192.168.1.1 255.255.255.252 ip ospf cost 0
B. router ospf 1 network 192.168.1.1 0.0.0.0 area 0 hello interval 15 interface e1/1 ip address 192.168.1.1 255.255.255.252
C. router ospf 1 network 192.168.1.1 0.0.0.0 area 0 interface e1/1 ip address 192.168.1.1 255.255.255.252 ip ospf network broadcast
D. router ospf 1 network 192.168.1.1 0.0.0.0 area 0 interface e1/1 ip address 192.168.1.1 255.255.255.252 ip ospf network point-to-point

Selected Answer: D

Question #: 464
Topic #: 1
Refer to the exhibit. An engineer is updating the R1 configuration to connect a new server to the management network. The PCs on the management network must be blocked from pinging the default gateway of the new server. Which command must be configured on R1 to complete the task?

A. R1(config)#ip route 172.16.2.0.255.255.255.0 192.168.1.15
B. R1(config)#ip route 172.16.2.2 255.255.255.248 gi0/1
C. R1(config)#ip route 172.16.2.2 255.255.255.255 gi0/0
D. R1(config)#ip route 172.16.2.0 255.255.255.0 192.168.1.5

Selected Answer: C

Question #: 465
Topic #: 1
Refer to the exhibit. Router R1 currently is configured to use R3 as the primary route to the internet, and the route uses the default administrative distance settings. A network engineer must configure R1 so that it uses R2 as a backup, but only if R3 goes down. Which command must the engineer configure on R1 so that it correctly uses R2 as a backup route, without changing the administrative distance configuration on the link to R3?

A. ip route 0.0.0.0 0.0.0.0 209.165.201.5.10
B. ip route 0.0.0.0 0.0.0.0 g0/1 1
C. ip route 0.0.0.0 0.0.0.0 209.165.200.226 1
D. ip route 0.0.0.0 0.0.0.0 g0/1 6

Selected Answer: D

Question #: 466
Topic #: 1
Refer to the exhibit. Which action must be taken to ensure that router A is elected as the DR for OSPF area 0?

A. Configure the router A interfaces with the highest OSPF priority value within the area
B. Configure router B and router C as OSPF neighbors of router A
C. Configure the OSPF priority on router A with the lowest value between the three routers.
D. Configure router A with a fixed OSPF router ID

Selected Answer: A

Question #: 467
Topic #: 1
Refer to the exhibit. Packets received by the router from BGP enter via a serial interface at 209.165.201.10. Each route is present within the routing table. Which interface is used to forward traffic with a destination IP of 10.10 10 24?

A. F0/10
B. F0/11
C. F0/12
D. F0/1

Selected Answer: B

Question #: 468
Topic #: 1
Refer to the exhibit. If OSPF is running on this network, how does Router2 handle traffic from Site B to 10.10.13.128/25 at Site A?

A. It sends packets out of interface Fa0/1.
B. It sends packets out of interface Fa0/2.
C. It load-balances traffic out of Fa0/1 and Fa0/2.
D. It is unreachable and discards the traffic.

Selected Answer: D

Question #: 469
Topic #: 1
Refer to the exhibit. Router R1 resides in OSPF Area 0. After updating the R1 configuration to influence the paths that it will use to direct traffic, an engineer verified that each of the four Gigabit interfaces has the same route to 10 10.0.0/16.
Which interface will R1 choose to send traffic to reach the route?

A. GigabitEthernet0/0
B. GigabitEthernet0/1
C. GigabitEthernet0/2
D. GigabitEthernet0/3

Selected Answer: B

Question #: 470
Topic #: 1
Refer to the exhibit. Which network prefix was learned via EIGRP?

A. 172.160.0/16
B. 207.165.200.0/24
C. 192.168.1.0/24
D. 192.168.2.0/24

Selected Answer: D

Question #: 471
Topic #: 1
Refer to the exhibit. Which command must be issued to enable a floating static default route on router A?

A. ip route 0.0.0.0 0.0.0.0 192.168.1.2 10
B. ip route 0.0.0.0 0.0.0.0 192.168.1.2
C. ip default-gateway 192.168.2.1
D. ip route 0.0.0.0 0.0.0.0 192.168.2.1 10

Selected Answer: A

Question #: 472
Topic #: 1
Refer to the exhibit. Which configuration allows routers R14 and R86 to form an OSPFv2 adjacency while acting as a central point for exchanging OSPF information between routers?

A. R14# interface FastEthernet0/0 ip address 10.73.65.65 255.255.255.252 ip ospf network broadcast ip ospf priority 0 ip mtu 1400 router ospf 10 router-id 10.10.1.14 network 10.10.1.14 0.0.0.0 area0 network 10.73.65.64 0.0.0.3 area0 R86# interface Loopback0 ip address 10.10.1.86 255.255.255.255 interface FastEthernet0/0 ip address 10.73.65.66 255.255.255.252 ip ospf network broadcast ip mtu 1500 router ospf 10 router-id 10.10.1.86 network 10.10.1.86 0.0.0.0 area 0 network 10.73.65.64 0.0.0.3 area 0
B. R14# interface Loopback0 ip ospf 10 area 0 interface FastEthernet0/0 ip address 10.73.65.65 255.255.255.252 ip ospf network broadcast ip ospf 10 area 0 ip mtu 1500 router ospf 10 ip ospf priority 255 router-id 10.10.1 14 R86# interface Loopback0 ip ospf 10 area 0 interface FastEthernet0/0 ip address 10.73.65.66 255.255.255.252 ip ospf network broadcast ip ospf 10 area 0 ip mtu 1500 router ospf 10 router-id 10.10.1.86
C. R14# interface FastEthernet0/0 ip address 10.73.65.65 255.255.255.252 ip ospf network broadcast ip ospf priority 255 ip mtu 1500 router ospf 10 router-id 10.10.1.14 network 10.10.1.14 0.0.0.0 area0 network 10.73.65.64 0.0.0.3 area0 R86# interface FastEthernet0/0 ip address 10.73.65.66 255.255.255.252 ip ospf network broadcast ip mtu 1500 router ospf 10 router-id 10.10.1.86 network 10.10.1.86 0.0.0.0 area 0 network 10.73.65.64 0.0.0.3 area 0
D. R14# interface FastEthernet0/0 ip address 10.73.65.65 255.255.255.252 ip ospf network broadcast ip ospf priority 255 ip mtu 1500 router ospf 10 router-id 10.10.1.14 network 10.10.1.14 0.0.0.0 area0 network 10.73.65.64 0.0.0.3 area0 R86# interface FastEthernet0/0 ip address 10.73.65.66 255.255.255.252 ip ospf network broadcast ip mtu 1400 router ospf 10 router-id 10.10.1.86 network 10.10.1.86 0.0.0.0 area 0 network 10.73.65.64 0.0.0.3 area 0

Selected Answer: C

Question #: 473
Topic #: 1
Refer to the exhibit. When an administrator executes the show ip route command on router D to view its routing table, which value is displayed for the administrative distance for the route to network 192.168 1.0?

A. 110
B. 120
C. 170
D. 90

Selected Answer: A

Question #: 474
Topic #: 1
Refer to the exhibit Routers R1 and R2 have been configured with their respective LAN interfaces. The two circuits are operational and reachable across WAN.
Which command set establishes failover redundancy if the primary circuit goes down?

A. R1(config)#ip route 0.0.0.0 0.0.0.0 10.10.10.6 R2(config)#ip route 0.0.0.0 0.0.0.0 10.10.10.5
B. R1(config)#ip route 10.10.13.10 255.255.255.255 10.10.10.2 R2(config)#ip route 192.168.0.100 255.255.255.255 10.10.10.1
C. R1(config)#ip route 10.10.13.10 255.255.255.255 10.10.10.6 R2(config)#ip route 192.168.0.100 255.255.255.255 10.10.10.5
D. R1(config)#ip route 0.0.0.0 0.0.0.0 10.10.10.6 2 R2(config)#ip route 0.0.0.0 0.0.0.0 10.10.10.5 2

Selected Answer: D

Question #: 475
Topic #: 1
Refer to the exhibit. R1 learns all routes via OSPF. Which command configures a backup static route on R1 to reach the 192.168.20 0/24 network via R3?

A. R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2 111
B. R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2 90
C. R1(config)#ip route 192.168.20.0 255.255.0.0 192.168.30.2
D. R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2

Selected Answer: A

Question #: 476
Topic #: 1
Refer to the exhibit. R1 learns all routes via OSPF. Which command configures a backup static route on R1 to reach the 192.168.20 0/24 network via R3?

Selected Answer: A

Question #: 477
Topic #: 1
Refer to the exhibit. R1 has taken the DROTHER role in the OSPF DR/BDR election process. Which configuration must an engineer implement so that R1 is elected as the DR?

A. R1(config)#interface FastEthernet 0/0 R1(config-if)#ip ospf priority 1 R1#clear ip ospf process
B. R3(config)#interface FastEthernet 0/1 R3(config-if)#ip ospf priority 200 R3#clear ip ospf process
C. R2(config)#interface FastEthernet 0/2 R2(config-if)#ip ospf priority 1 R2#clear ip ospf process
D. R1(config)#interface FastEthernet 0/0 R1(config-if)#ip ospf priority 200 R1#clear ip ospf process

Selected Answer: D

Question #: 478
Topic #: 1
Which SDN plane forwards user-generated traffic?

A. Management plane
B. Control plane
C. Policy plane
D. Data plane

Selected Answer: D

Question #: 479
Topic #: 1
An application in the network is being scaled up from 300 servers to 600. Each server requires 3 network connections to support production, backup, and management traffic. Each connection resides on a different subnet. The router configuration for the production network must be configured first using a subnet in the 10.0.0.0/8 network. Which command must be configured on the interface of the router to accommodate the requirements and limit wasted IP address space?

A. ip address 10.10.10.1 255.255.254.0
B. ip address 10.10.10.1 255.255.252.0
C. ip address 10.10.10.1 255.255.240.0
D. ip address 10.10.10.1 255.255.255.240

Selected Answer: B

Question #: 480
Topic #: 1
Refer to the exhibit. Which interface is chosen to forward traffic to the host at 192.168.0.55?

A. GigabitEthernet0/3
B. Null0
C. GigabitEthernet0/1
D. GigabitEthernet0/2

Selected Answer: C

Cart

Practice Exam

Install openssl-1.0.2k on Amazon Linux 2023

Protect Your System: Understanding CVE-2024-3400 Zero-Day Vulnerability

Cart